Doing it Right – How to Hold TPO Down During Application of Adhesive

By Thomas J Taylor PhD 12-21-2022
QUICK SHARE
Tag Icon

Introduction

We all recognize that, when properly installed, TPO can be part of a well performing roof system. However, a very simple error made during installation can set up the membrane for future issues. This has been known since early installations of TPO roofs but somehow it has been forgotten about by many installers. What are we talking about here? The use of adhesive buckets along a fold that causes premature cracking of the membrane years after installation. Let's dig deeper.

Background

The Western States Roofing Contractors Association, WSRCA, had the foresight to install test areas of TPO from four manufacturers in 2000/2001. Four roofs were involved, located in different climate regions of the western US. Each roof had four sections completed with TPO from the different manufacturers. Approximately every other year after installation the roofs were inspected and test cuts taken, until the tenth year. There were many findings, including the overall impression that TPO did not erode or weather significantly over that time frame.

  • But, the "most significant" finding at the 10 year point was the severity of cracks that had formed at hard creases put into the membranes during installation.

Hard Creases in TPO

When adhered TPO is installed with solvent based adhesive it must be applied to both the substrate and the membrane. This means that, after the TPO is rolled out, it is folded back on itself lengthwise. To hold the membrane in place, installers typically use adhesive buckets. There are two ways to do this; one right and one wrong.

So let's look at the installation of TPO using a spray adhesive:

Crew

Notice how the TPO is loosely folded over itself. One installer is keeping the TPO steady while the other is spraying the adhesive. Important - the TPO is not creased.

Now let's look at the installation of TPO using a conventional solvent based adhesive:

TPO

The crew are using adhesive buckets to hold down the TPO. IMPORTANT - the buckets are well back from the TPO folds and there's no risk of a hard crease. This is how an application of adhesive should be done - NO HARD CREASES!

Let's look at how not to do it:

TPO

This crew has placed the adhesive bucket directly on top of the TPO fold. This will lead to a hard crease and potential TPO cracking down the road. The best way to avoid this potential problem is to NEVER HARD CREASE TPO!

Bottom Line

    • Hard creasing of TPO during installation frequently leads to cracks in the membrane after years of weathering.

    • Make sure that the membrane is loosely folded when preparing for an adhered installation.

    • Never place weights of any kind directly onto a membrane fold.

Don't miss another GAF RoofViews post!
LATEST UPDATES
To get a firsthand account of what it's like to be a roofer, GAF spoke with Trenton Wisecup, president of Arrow Roofing Services in Michigan, and David Laurain, Arrow Roofing's vice president, to learn about their experiences in the roofing industry.
Historically, commercial skylights have gotten a bad rap. "The old joke was: 'if it's not leaking now, it will be soon,'" says Brian Grohe, a 13-year vet of the skylight industry and a commercial sales manager at industry leader VELUX. Fortunately, technology has changed that old tune for the better, turning commercial skylights into a golden opportunity for roofing contractors.
Around the globe, excess heat collects in urban areas and can contribute to increased heat-related death and illness, diminished quality of life, and reduced economic opportunities. Such areas are known as "urban heat islands." Fortunately, cooling strategies are now available and being used in initiatives like the GAF Cool Community project to help mitigate urban heat island effects. Such cooling strategies are supported by products such as such as GAF StreetBond® pavement coatings with Invisible Shade™ — named by TIME magazine as one of its Best Inventions of 2022.
The GAF manufacturing plant in Tuscaloosa, Alabama sits just a half mile away from Stillman College, a historically Black university with a rich history in the area. The school was first formed as the Tuscaloosa Institute in 1875 by the Presbyterian Church to serve as a ministerial training academy for Black men. It was renamed in 1899 — after the director whose idea it was to found the academy — Rev. Dr. Charles Allen Stillman.
Critically acclaimed actor — with a roofing industry background — Anthony Mackie has teamed up with GAF and their Community Matters initiative to help rebuild Gulf Region roofs hit by extreme weather.
It's easy to think that there are as many roof types as there are buildings. In truth, there are only a few standard kinds and variations are made by combinations of these. The type of roof you select for your home or addition will influence a lot of other factors, including overall cost, what materials you can use, and how much of the roof is visible from the street.
This blog contains information created by a variety of sources, including internal and third party writers. The opinions and views expressed do not necessarily represent those of GAF. The content is for informational purposes only. It is not intended to constitute financial, accounting, tax or legal advice. GAF does not guarantee the accuracy, reliability, and completeness of the information. In no event shall GAF be held responsible or liable for errors or omissions in the content or for the results, damages or losses caused by or in connection with the use of or reliance on the content.

Interested in sharing or republishing our content? We kindly ask you to adhere to our guidelines.